Comment résoudre le problème de surchauffe de l'iPhone 12 Pro Max avec des cosses de soudure

Comment résoudre le problème de surchauffe de l'iPhone 12 Pro Max avec des cosses de soudure

Today we will share how to fix iPhone 12 Pro Max overheating or temperature warning issue. The phone has been dropped before and the screen is cracked. After boot-up, the phone shows a temperature warning.

how fix iphone 12 pro max overheating issue soldering lugs ov

Next, we take apart the phone for testing. Disconnect the flex cables. Remove the motherboard. In the first place, we check if the motherboard is deformed. The motherboard is not deformed.

how fix iphone 12 pro max overheating issue soldering lugs ov 2

It can be seen under the microscope that the motherboard has pseudo-soldering. Then we need to separate the motherboard.

how fix iphone 12 pro max overheating issue soldering lugs ov 3

Detach the foam and plastic part. Put the motherboard on the 165 °C Plate-forme de chauffage to heat. Since the middle layer of iPhone 12 lineup adopts middle-temperature solder paste for soldering, we need to assist the heating with a Hot Air Gun at 330 °C. Try to pry up the logic board with a Pry Blade while heating. If the logic board becomes loose, remove it. Then remove the signal board.

Fix iPhone 12 Pro Max Overheating Issue by Soldering Lugs - Over a Dozen Missing Pads

It can be seen under the microscope that pads on the logic board are missing. Then we need to repair the bonding pads. Clean the bonding pads with Fer à souder at 380 °C and Solder Wick. Next, clean the bonding pads with PCB Cleaner.

how fix iphone 12 pro max overheating issue soldering lugs ov 5
how fix iphone 12 pro max overheating issue soldering lugs ov 6

Then scrape the missing pads to show the circuits with a Sculpture Knife. Please pay attention not to damage the GND while scraping.

how fix iphone 12 pro max overheating issue soldering lugs ov 7

Clean the bonding pads with PCB Cleaner. Apply tin to the bonding pads with a Soldering Iron.

how fix iphone 12 pro max overheating issue soldering lugs ov 8

Then we put the Soldering Lugs in position. Apply some Paste Flux. Heat with a Soldering Iron to solder. Clean the bonding pads with PCB Cleaner.

how fix iphone 12 pro max overheating issue soldering lugs ov 9

Apply some Solder Mask to the bonding pads. Then solidify with a UV Lamp. After solidifying, remove excess solder mask with a Sculpture Knife to show the pads.

how fix iphone 12 pro max overheating issue soldering lugs ov 10
how fix iphone 12 pro max overheating issue soldering lugs ov 11
how fix iphone 12 pro max overheating issue soldering lugs ov 12

Clean the bonding pads with PCB Cleaner. Then clean the bonding pads with Soldering Iron and Solder Wick. Keep cleaning the bonding pads with a Dust-free Wipe.

how fix iphone 12 pro max overheating issue soldering lugs ov 13
how fix iphone 12 pro max overheating issue soldering lugs ov 14

Next, we reball the signal board. Attach the signal board to the holder. Put the reballing stencil in position. Apply some low-temperature Solder Paste evenly. Remove excess solder paste.

how fix iphone 12 pro max overheating issue soldering lugs ov 15

Detach the reballing stencil. Put the motherboard on the 165 °C Heating Platform to heat for recombination. Remove the motherboard after it has cooled for 5 minutes.

how fix iphone 12 pro max overheating issue soldering lugs ov 16

Install the motherboard for testing. Connect the screen. The phone turns on normally. The temperature warning has disappeared.

how fix iphone 12 pro max overheating issue soldering lugs ov 17

Laisser un commentaire

Votre adresse e-mail ne sera pas publiée. Les champs obligatoires sont indiqués avec *

Défiler vers le haut