Xiaomi 10 Cannot Boot After Screen Replacement

Xiaomi 10 Cannot Boot After Screen Replacement

Xiaomi 10 Cannot Boot After Screen Replacement

Model: Xiaomi Mi10

Announced: 2020, February 13

xiaomi 10 cannot boot screen replacement

Defect Phenomenon

First, it was only the screen cracked, and the client tried to replace a new screen by himself, but during the replacement, damaged a flex cable. Bought a new flex cable and replace it, then find the phone cannot be booted.

xiaomi 10 cannot boot screen replacement first only the is cracked

Send the phone to a repair shop, and the repair technician judge it’s the CPU with a problem. After resoldering the CPU, assembling the phone, and testing, the issue still remains the same.

Troubleshooting

xiaomi 10 cannot boot screen replacement check the motherboard cpu has

Check the motherboard, it’s obvious that the CPU has been resoldered before.

Normally, the repair technician will not take the second repair cellphone or board. As we don’t know which part and how it was repaired before, the repair difficulty level is very high! However, there are very important data inside, and the client begs us to repair it for him. So finally, we decide to have a try. 

The client damaged flex cable is the connection cable between the display little board and the motherboard.

xiaomi 10 cannot boot screen replacement the damaged flex cable is

The display chip is independently integrated into this little board

xiaomi 10 cannot boot screen replacement the display chip is indepently

Get the flex cable and the boards connected, then power with the DC power supply machine to have a test

xiaomi 10 cannot boot screen replacement get the flex cable and boards

The boot current jumps to around 260mA then drops down

xiaomi 10 cannot boot screen replacement the current jumps to around

Based on the repair experience, this kind of abnormal current is caused by the CPU or the UFS. Besides, the Xiaomi 10 is equipped with Snapdragon 865, which is very easy to hot to cause the CPU poor soldering. So the previous repair technician’s repair logic (resolder the CPU) is OK.

Xiaomi 10 should get the battery connected first, then the phone can boot normally. So let’s connect the motherboard with the battery and connect the charging cable to boot. As we can see, there’s no charging current at all.

xiaomi 10 cannot boot screen replacement charge with charging cable

Let’s try to boot again with the charging cable connected but the battery connector detached.

xiaomi 10 cannot boot screen replacement lets try to again with charging

There is a 0.2A charging current

xiaomi 10 cannot boot screen replacement there is 2a charging current

By the above phenomenon, we can make a preliminary judgment, it’s the battery current detecting pins with a problem. Let’s take out the motherboard and measure the diode values on the battery connector J5400

xiaomi 10 cannot boot screen replacement take out the motherboard and

Refer to the bitmap (or you can measure the diode value on a good motherboard for reference ) to measure the battery data pins

xiaomi 10 cannot boot screen replacement measure the diode value on

The pin 3 (BATT_B+_J2) diode value should be around 589, but the measured result is OL. There must be something wrong with this rail, might be an inside rail broken.

xiaomi 10 cannot boot screen replacement the pin batt j2 diode value

On the bitmap, we can see that battery pin 3 is connected with the test point

xiaomi 10 cannot boot screen replacement the connection rails

And the measured diode value on the test point is 555, which is normal.

xiaomi 10 cannot boot screen replacement the diode value of test point

Jump a wire from Pin 3 of the battery connector to the test point

xiaomi 10 cannot boot screen replacement jump wire from pin of the

Then measure the diode value on pin 3 of J5400 again, and the diode value back to normal.

xiaomi 10 cannot boot screen replacement measure the diode value again

Then let’s put the motherboard into the phone cover to have a test

  • Get the battery connected
  • Plug in the charging cable

The phone can be booted normally, enter the PIN code to enter into the system and test the functions, all are OK.

Apply the UV mask on the jump wire, then cure with a UV lamp to fix and isolate.

xiaomi 10 cannot boot screen replacement apply the uv mask on jumped

In the last step, let’s assemble the phone and apply more thermal grease on the CPU, and test again. Everything works fine, the issue gets perfectly resolved by jumping the wire on the battery data pin.

Xiaomi 10 Cannot Boot

>>> Visit REWA Academy to light up your repair skills

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top